AS-110

AS-110 Datasheet


AS-100 AS-101 AS-102 AS-103 AS-104 AS-105 AS-110 AS-111 AS-112 AS-113 AS-114 AS-115

Part Datasheet
AS-110 AS-110 AS-110 (pdf)
Related Parts Information
AS-320 AS-320 AS-320
AS-312 AS-312 AS-312
AS-311 AS-311 AS-311
AS-302 AS-302 AS-302
AS-332 AS-332 AS-332
AS-405 AS-405 AS-405
AS-310 AS-310 AS-310
AS-321 AS-321 AS-321
AS-322 AS-322 AS-322
AS-406 AS-406 AS-406
AS-404 AS-404 AS-404
AS-330 AS-330 AS-330
AS-331 AS-331 AS-331
AS-402 AS-402 AS-402
AS-301 AS-301 AS-301
AS-403 AS-403 AS-403
AS-400 AS-400 AS-400
AS-113 AS-113 AS-113
AS-111 AS-111 AS-111
AS-103 AS-103 AS-103
AS-102 AS-102 AS-102
AS-101 AS-101 AS-101
AS-105 AS-105 AS-105
AS-114 AS-114 AS-114
AS-115 AS-115 AS-115
AS-112 AS-112 AS-112
AS-104 AS-104 AS-104
AS-407 AS-407 AS-407
AS-211 AS-211 AS-211
AS-300 AS-300 AS-300
AS-202 AS-202 AS-202
AS-210 AS-210 AS-210
AS-201 AS-201 AS-201
AS-200 AS-200 AS-200
AS-401 AS-401 AS-401
AS-100 AS-100 AS-100
PDF Datasheet Preview
AS Series
• Current Sense Inductors & Transformers

AS Series Current Sensors are designed as a low cost method of controlling, monitoring or measuring AC currents. The sensors serve as feedback elements between the output and pulse control circuitry providing accurate regulation of switch mode power supplies.
• Fully encapsulated for optimal PC board mounting
• Frequency range from 20kHz to 200kHz
• Primary current rating to 30 Amps
• Primary to secondary isolated to 2500 VAC
• Meets VDE norms
• Optimum performance over designated current and
frequency range
• Competitive pricing due to high volume production
• Manufactured in an ISO-9001:2000, TS-16949:2002
and ISO-14001:2004 certified facility
• Fully RoHS compliant

Isolated current feed-back signal in Switch Mode Power Supplies
• Motor current load/overload
• LighStiwngitch C• ontrols Ultra-sound current
• High resolution sonar current
• Isolated bi-directional current sensor with full wave bridge rectifier

Electrical Specifications at 25°C

AS-100 AS-101 AS-102 AS-103 AS-104 AS-105 AS-110 AS-111 AS-112 AS-113 AS-114 AS-115

Prim./Sec. Ratio
1:50 1:100 1:200 1:300 1:500 1:750 1:50CT 1:100CT 1:200CT 1:300CT 1:500CT 1:750CT

Lsec 1 mH Min
6 25 100 250 700 1682 6 25 100 250 700 1682

DCRsec Ohms Max.
/ / / / / /

Sec. Term. 2 Resistance

Ohms Nom.
50 100 200 300 500 750 25 + 25 50 + 50 100 + 100 150 + 150 250 + 250 375 + 375

Isec 3 Max.
300mA 150mA 75mA 50mA 30mA 40mA 300mA 150mA 75mA 50mA 30mA 40mA

Volt µS 4 Max.
175 350 700 900 1500 3750 175 350 700 900 1500 3750

Schematic
1 Lsec Secondary inductance tested at 10kHz and 10mV for 1:50 through 1:500 Prim./Sec. ratios and 1kHz/10mV for Prim./Sec. ratio of 1:750
2 This nominal termination resistance value will yield approximately 1.0V
of output for each amp of current in a single turn sense line. The output

Voltage/Ampere of these devices can be increased or decreased linearly
over a restricted temperature range by adjusting the terminating resistance.
3 For Prim./Sec. Ratios of 1:50 through 1:500, the sIec value corresponds to a maximum primary current of 15 Amp-turns rms while the Isec value for the ratio of
1:750 corresponds to a max. primary current of 30 Amp-turns rms.

VµS = R t x Is x

Rt Ohms Recommended Terminating Resistance

Is A Secondary Current

F Hz Frequency
5 Operating Temperature Range -40°C to +120°C
6 Pin 2 is on Center-Tapped CT versions only

A0*,6

ASXXX

Primary Sense Current

AMGIS, LLC * 10830 Kinghurst Dr. Houston, TX 77099 Phone 832-775-1319 * Fax 281-933-9067* email:

Toll Free 877-762-6447 *

AS Series
• Current Sense Inductors & Transformers
More datasheets: AS-115 | AS-112 | AS-104 | AS-407 | AS-211 | AS-300 | AS-202 | AS-210 | AS-201 | AS-200


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AS-110 Datasheet file may be downloaded here without warranties.

Datasheet ID: AS-110 515968