ACS752SCA-100

ACS752SCA-100 Datasheet

ACS752SCA-100

Part	Datasheet
ACS752SCA-100	ACS752SCA-100 (pdf)

PDF Datasheet Preview
ACS752SCA-100 Fully Integrated, Hall Effect-Based Linear Current Sensor IC with High Voltage Isolation and a Low-Resistance Current Conductor Discontinued Product These parts are no longer in production The device should not be purchased for new design applications. Samples are no longer available. Date of status change May 4, 2009 Recommended Substitutions: For existing customer transition, and for new customers or new applications, refer to the ACS756. NOTE For detailed information on purchasing options, contact your local Allegro field applications engineer or sales representative. ACS752SCA-100 Fully Integrated, Hall Effect-Based Linear Current Sensor IC with High Voltage Isolation and a Low-Resistance Current Conductor Monolithic Hall IC for high reliability Single +5 V supply 3 kVRMS isolation voltage between terminals 4/5 and pins 1/2/3 for up to 1 minute 50 kHz bandwidth Automotive temperature range End-of-line factory-trimmed for gain and offset Ultra-low power loss 130 uΩ internal conductor resistance Ratiometric output from supply voltage Extremely stable output offset voltage Small package size, with easy mounting capability Output proportional to AC and DC currents Package 5 pin package leadform PFF The Allegro ACS75x family of current sensor ICs provides economical and precise solutions for current sensing in industrial, automotive, commercial, and communications systems. The device package allows for easy implementation by the customer. Typical applications include motor control, load detection and management, power supplies, and overcurrent fault protection. The device consists of a precision, low-offset linear Hall circuit with a copper conduction path located near the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage. Device accuracy is optimized through the close proximity of the magnetic signal to the Hall transducer. A precise, proportional voltage is provided by the low-offset, chopper-stabilized BiCMOS Hall IC, which is programmed for accuracy at the factory. The output of the device has a positive slope >VCC / 2 when an increasing current flows through the primary copper conduction path from terminal 4 to terminal 5 , which is the path used for current sampling. The internal resistance of this conductive path is typically 130 uΩ, providing low power loss. The thickness of the copper conductor allows survival of the device at up to Continued on the next 4 IP+ 1 VCC ACS752 GND 2 VIOUT CBYP µF CF RF VOUT Application The ACS752 outputs an analog signal, VOUT that varies linearly with the uni- or bi-directional AC or DC primary sampled current, IP , within the range specified. CF is recommended for noise management, with values that depend on the application. ACS752SCA-100 Fully Integrated, Hall Effect-Based Linear Current Sensor IC with High Voltage Isolation and a Low-Resistance Current Conductor Description continued 5x overcurrent conditions. The terminals of the conductive path are electrically isolated from the signal leads pins 1 through This allows the ACS75x family of sensor ICs to be used in applications requiring electrical isolation without the use of opto-isolators or other costly isolation techniques. The device is fully calibrated prior to shipment from the factory. The ACS75x family is lead Pb free. All pins are coated with 100% matte tin, and there is no lead inside the package. The heavy gauge leadframe is made of oxygen-free copper. Selection Guide TOP °C Primary Sampled Current, IP A Sensitivity Sens Typ. mV/A Packing1 ACS752SCA-1002

PDF Datasheet Preview

ACS752SCA-100

Fully Integrated, Hall Effect-Based Linear Current Sensor IC with High Voltage Isolation and a Low-Resistance Current Conductor

Discontinued Product

These parts are no longer in production The device should not be purchased for new design applications. Samples are no longer available.

Date of status change May 4, 2009

Recommended Substitutions:

For existing customer transition, and for new customers or new applications, refer to the ACS756.

NOTE For detailed information on purchasing options, contact your local Allegro field applications engineer or sales representative.

ACS752SCA-100

Fully Integrated, Hall Effect-Based Linear Current Sensor IC with High Voltage Isolation and a Low-Resistance Current Conductor

Monolithic Hall IC for high reliability Single +5 V supply 3 kVRMS isolation voltage between terminals 4/5 and
pins 1/2/3 for up to 1 minute 50 kHz bandwidth Automotive temperature range End-of-line factory-trimmed for gain and offset Ultra-low power loss 130 uΩ internal conductor
resistance Ratiometric output from supply voltage Extremely stable output offset voltage Small package size, with easy mounting capability Output proportional to AC and DC currents

Package 5 pin package leadform PFF

The Allegro ACS75x family of current sensor ICs provides economical and precise solutions for current sensing in industrial, automotive, commercial, and communications systems. The device package allows for easy implementation by the customer. Typical applications include motor control, load detection and management, power supplies, and overcurrent fault protection.

The device consists of a precision, low-offset linear Hall circuit with a copper conduction path located near the die. Applied current flowing through this copper conduction path generates a magnetic field which the Hall IC converts into a proportional voltage. Device accuracy is optimized through the close proximity of the magnetic signal to the Hall transducer. A precise, proportional voltage is provided by the low-offset, chopper-stabilized BiCMOS Hall IC, which is programmed for accuracy at the factory.

The output of the device has a positive slope >VCC / 2 when an increasing current flows through the primary copper conduction path from terminal 4 to terminal 5 , which is the path used for current sampling. The internal resistance of this conductive path is typically 130 uΩ, providing low power loss. The thickness of the copper conductor allows survival of the device at up to

Continued on the next
4 IP+
1 VCC

ACS752

GND 2

VIOUT

CBYP µF

CF RF

VOUT

Application The ACS752 outputs an analog signal, VOUT that varies linearly with the uni- or bi-directional AC or DC
primary sampled current, IP , within the range specified. CF is recommended for noise management, with values that
depend on the application.

ACS752SCA-100

Fully Integrated, Hall Effect-Based Linear Current Sensor IC with High Voltage Isolation and a Low-Resistance Current Conductor

Description continued 5x overcurrent conditions. The terminals of the conductive path are electrically isolated from the signal leads pins 1 through This allows the ACS75x family of sensor ICs to be used in applications requiring electrical isolation without the use of opto-isolators or other costly isolation techniques.

The device is fully calibrated prior to shipment from the factory. The ACS75x family is lead Pb free. All pins are coated with 100% matte tin, and there is no lead inside the package. The heavy gauge leadframe is made of oxygen-free copper.

Selection Guide

TOP °C

Primary Sampled

Current, IP A

Sensitivity Sens Typ.
mV/A

Packing1

ACS752SCA-1002

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ACS752SCA-100 Datasheet file may be downloaded here without warranties.

Datasheet ID: ACS752SCA-100 516108