AK5371
Part | Datasheet |
---|---|
![]() |
AK5371VQ (pdf) |
PDF Datasheet Preview |
---|
ASAHI KASEI AK5371 Features: - USB-IF Certified - Incorporates USB Audio Controller USB Serial Interface Engine Audio Class Encoder/Decoder 2 Endpoints FIFO USB transceiver - 16 bit A/D Converter 2 channels Mute/Volume Control A/D S/N 84dBA 44.1kHz, Gain = 0dB - Low Power Dissipation Normal Operation 26mA Suspend Mode < 1uA - Programmable Gain Amplifier IPGA +24dB to Step - 20dB Pre-amplifier - On-chip PLL 5 Sampling Frequencies support 8kHz, 11.025kHz 22.05kHz, 44.1kHz, 48kHz - EEPROM I/F can customize Device Descriptor, and String Descriptor - Single Power Supply, Low Power Volts - Package 48pin LQFP, 48pin QFN [AK5371] 2ch A/D Converter with USB I/F The AK5371 is stereo A/D converter with USB I/F. The AK5371 integrates USB serial interface engine, USB transceiver, audio class processing unit, endpoints, and high quality 2 channel AD converter into the chip. As the AK5371 incorporates PLL, it can support several sampling frequencies, 8kHz, 11.025kHz, 22.05kHz, 44.1kHz, and 48kHz with only one crystal. Moreover, the AK5371 integrates volume control, and mute function. Not only power consumption at normal operation is very low, but also the current at suspend mode is less than 1µA. The AK5371 includes 20dB fixed gain pre-amplifier. In addition to this, as the AK5371 also incorporates IPGA which can amplify the microphone signal up to +24dB, total gain is 44dB maximum. The AK5371 has EEPROM I/F for customizing Device Descriptor and String Descriptor. By connecting 1K bit, 2K bit, or 4Kbit MicrowireTM type EEPROM, the AK5371 can customize Vendor ID, Product ID in Device Descriptor, and String Descriptor. This device is good for not only business application such as conferencing but also games, voice recognition, and Karaoke. Related Documents For the detail of USB specification, and Audio Class, please refer to the following documents. MS0466-E-00 MS0103-E-00 2006/02 ASAHI KASEI [AK5371] - Block Diagram BGND MICBIAS MICR 20dB - AMPR1O AMPR2I MICL 20dB - AMPL1O AMPL2I BIASSEL VA VREF VCOM AGND VD DGND SUSN VREF Common Voltage Config/String ROM - Ordering Guide AK5371VQ AK5371VN AKD5371 0 ~ +70 °C 48pin LQFP 0.5mm pitch 0 ~ +70 °C 48pin QFN 0.4mm pitch Evaluation Board - Pin Layout NC EPDI EPEN EPSEL NC SUSN RSTN NC DP DN NC VD DGND BGND NC TESTMODE3 XTALOUT XTALIN TESTMODE2 LFLT1 LFLT2 BIASSEL NC 45 1 5 10 15 40 20 EPAO TEST TESTMODE1 VREF AGND AMPR2O AMPR2I AMPR1O MICR NC AMPL2O AMPL2I AMPL1O MICL MICBIAS VCOM NC MS0466-E-00 MS0103-E-00 2006/02 ASAHI KASEI [AK5371] Signal Name 2 DGND 3 BGND 5 TESTMODE3 6 XTALOUT 7 XTALIN 8 TESTMODE2 9 LFLT1 10 LFLT2 11 BIASSEL 12 NC 13 NC 14 VCOM 15 MICBIAS <REMARK> This drawing does NOT mean physical pin locations/ordering R1:4.7k 10uH 0.1u Regulator 0.1u 100u 0.1u 4.7u 0.1u 4.7u 0.1u 4.7u 0.1u 4.7u 0.1u R1:4.7k VREF VCOM MICBIAS VA AGND BGND VD DGND RSTN 0.1u 100u C1:1.0u< C2:0.33u C1:1.0u< Phone Jack STEREO SW C2:0.33u MICR AMPR1O AMPR2I MICL AMPL1O AMPL2I AMP2RO AMP2LO CS SK EPAO EPDI Testmode 1 Testmode 2 Testmode 3 Test DN LFLT1,2 XTALOUT XTALIN 56k 10u 3300p EEPROM 1.5k D+ To Host/Hub 51k C3:1000p C3:1000p 8200p 1M 18k 11.2896M 6800p Cd 5V GND analog GND digital GND C1 is specified for lower end cut-off frequency C3 forms Anti-aliasing filter in conjuction with the internal resistor at AMPR2O/AMPL2O R0 resister when BIASSEL is Low. resister when BIASSEL is High Cd Please select the appropriate value according to crystal resonator’s characteristics MS0466-E-00 MS0103-E-00 2006/02 ASAHI KASEI AK5371 Descriptors Specification [AK5371] 1 Device descriptor Offset 0 1 2 4 5 6 7 8 10 12 14 15 16 17 |
More datasheets: 99426-0016T | 99440-0016T | 99420-0016T | 99450-0016T | 99424-0016T | 99460-0016T | 99410-0016T | 99414-0016T | 99416-0016T | 99436-0016T |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AK5371VQ Datasheet file may be downloaded here without warranties.