IDK-101R-44WSI1

IDK-101R-44WSI1 Datasheet

IDK-101R-44WSI1

Part	Datasheet
IDK-101R-44WSI1	IDK-101R-44WSI1 (pdf)

PDF Datasheet Preview
Mar 5th, 2012 Version IDK-101R-44WSI1 Author Jerry.Huang E-mail: 1 General Description and Features 10 inch is Amorphous-TFT-LCD Thin Film Transistor Liquid Crystal Display module. This module is composed of a 10” TFT-LCD panel, a driving circuit and backlight system. This TFT LCD has a 10 17:10 inch diagonally measured active display area with WSVGA 1024 horizontal by 600 vertical pixel resolution. 2 Physical specifications ABSOLUTE MAX. RATINGS GND = AVSS = 0V Mechanical Information 5 ELECTRICAL CHARACTERISTICS 5-1 Typical Operation Conditions Note 1 VDD-dip condition when condition should be same as VDD-turn-con Condition. 5-2 Switching Characteristics for LVDS Receiver 5-3 Bit Mapping & Interface Definition Optical Specifications Measuring surrounding ● dark room ● LED current IL=160mA ● Ambient ● 15min. Warm-up time. Measuring Equipment The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are measured at the center point of the LCD screen. Response time is measured by Photo detector TOPCON BM-7 of view 1° / Height 120mm. Note 1 Definition of viewing angle range Note 2 Definition of Contrast Ratio CR measured at the center point of panel Note 3 Definition of Response time Sum of TR and T Note 4 Definition of optical measurement setup Note 5 Definition of brightness uniformity INTERFACE TFT LCD Module CN1 Input signal FI-XB30SL-HF10 JAE or equivalent CN2 LED backlight BHSR-02VS-1 JST or equivalent CN3 LED backlight Driver FPHTI-104TTW000 Kingfont or equivalent Backlight Driving Conditions Note 1 There are 3 Groups LED shown as below , VLEDA-LEDK=18.9V ,Ta=25℃ Note2 Condition Ta=25℃, continuous lighting Life time is estimated data. Definitions of failure LCM brightness becomes half of the minimum value. LED doesn’t light normally. PWM Dimming Control Interface Timing DE mode Timing Diagram of Interface Signal DE mode Power On/Off Sequence 1 The supply voltage of the external system for the module input should be the same as the definition of VDD. 2 Apply the lamp voltage within the LCD operation range. When the back-light turns on before the LCD operation or the LCD turns off before the back-light turns off, the display may momentarily become white. 3 In case of VDD = off level, please keep the level of input signal on the low or keep a high impedance. 4 TP4 should be measured after the module has been fully discharged between power off and on period. 5 Interface signal shall not be kept at high impedance when the power is on. RELIABILITY TEST CONDITIONS Storage / Operating temperature Note .Max wet bulb temp.=39oC 12 OUTLINE DIMENSION LCM OUTLINE DIMENSION LED driver EDID TABLE

PDF Datasheet Preview

Mar 5th, 2012 Version

IDK-101R-44WSI1

Author Jerry.Huang E-mail:
1 General Description and Features
10 inch is Amorphous-TFT-LCD Thin Film Transistor Liquid Crystal Display module. This module is composed of a 10” TFT-LCD panel, a driving circuit and backlight system. This TFT LCD has a 10 17:10 inch diagonally measured active display area with WSVGA 1024 horizontal by 600 vertical pixel resolution.
2 Physical specifications

ABSOLUTE MAX. RATINGS

GND = AVSS = 0V

Mechanical Information
5 ELECTRICAL CHARACTERISTICS
5-1 Typical Operation Conditions

Note 1 VDD-dip condition when condition should be same as VDD-turn-con Condition.
5-2 Switching Characteristics for LVDS Receiver
5-3 Bit Mapping & Interface Definition

Optical Specifications

Measuring surrounding
● dark room ● LED current IL=160mA ● Ambient ● 15min. Warm-up time.

Measuring Equipment The optical characteristics should be measured in dark room. After 30 minutes
operation, the optical properties are measured at the center point of the LCD screen. Response time is measured by Photo detector TOPCON BM-7 of view 1° / Height 120mm.

Note 1 Definition of viewing angle range

Note 2 Definition of Contrast Ratio CR measured at the center point of panel Note 3 Definition of Response time Sum of TR and T Note 4 Definition of optical measurement setup Note 5 Definition of brightness uniformity

INTERFACE

TFT LCD Module CN1 Input signal FI-XB30SL-HF10 JAE or equivalent

CN2 LED backlight BHSR-02VS-1 JST or equivalent CN3 LED backlight Driver FPHTI-104TTW000 Kingfont or equivalent

Backlight Driving Conditions

Note 1 There are 3 Groups LED shown as below , VLEDA-LEDK=18.9V ,Ta=25℃

Note2 Condition Ta=25℃, continuous lighting Life time is estimated data. Definitions of failure LCM brightness becomes half of the minimum value. LED doesn’t light normally.

PWM Dimming Control Interface Timing DE mode

Timing Diagram of Interface Signal DE mode

Power On/Off Sequence
1 The supply voltage of the external system for the module input should be the same as the definition of VDD. 2 Apply the lamp voltage within the LCD operation range. When the back-light turns on before the LCD operation or the LCD turns off before the back-light turns off, the display may momentarily become white. 3 In case of VDD = off level, please keep the level of input signal on the low or keep a high impedance. 4 TP4 should be measured after the module has been fully discharged between power off and on period. 5 Interface signal shall not be kept at high impedance when the power is on.

RELIABILITY TEST CONDITIONS

Storage / Operating temperature Note .Max wet bulb temp.=39oC
12 OUTLINE DIMENSION LCM

OUTLINE DIMENSION LED driver

EDID TABLE

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived IDK-101R-44WSI1 Datasheet file may be downloaded here without warranties.

Datasheet ID: IDK-101R-44WSI1 515752