564 564 Datasheet

PRODUCT ID 564

Part	Datasheet
564	564 (pdf)

PDF Datasheet Preview
EL wire 4xAAA pocket inverter PRODUCT ID 564 A small, portable inverter for EL wire. Powers off of 4 AAA batteries not included! , it can drive meters 10 to 13 feet of our EL wire OR 1 meter 3 feet of EL tape OR a 10cmx10cm piece of EL panel for about 7 hours. There is a switch for selecting steady/blink/off modes. Comes with four 2.5mm pitch female JST connectors, standard for all the EL wire and tape we carry. The JST cables snap into the inverter, so if you don't need all 4 cables, you can use as few as you want. The inverter does not 'sequence' the 4 cables, so if you use 'blink mode' all the strands will blink at the same time. There is a 1.7mm DC jack on the side so you can put in to power this off of a different battery or power source, This cable has a matching DC plug on the end You can plug any of our EL wire/tape into this inverter directly. To connect a 'raw' piece EL wire to this, you'll want a male connector wire The EL inverter requires a 'load' to stabilize itself. Do not run the inverter without at least 2 ft of EL wire attached! Otherwise the inverter can spike and damage itself Like all inverters we've used, the 2000 Hz oscillation is slightly audible. To reduce the squeaking, we suggest opening up the case padding it with thick foam tape/weatherstripping. Squirting some hot glue around the capacitors may also help. We managed to get it silent this way. Check out our EL TRON bag tutorial for ideas! Soldering to raw EL wire is a little tricky but luckily we wrote a detailed tutorial! The tutorial also covers a lot of information about EL and how it works. Technical Details Dimensions o Inverter Size 85mm x 55mm x 22mm 3.4in x 2.2in x 0.85in o JST cable length approx. 20 cm o Weight without batteries 60g

PDF Datasheet Preview

EL wire 4xAAA pocket inverter

PRODUCT ID 564

A small, portable inverter for EL wire. Powers off of 4 AAA batteries not included! , it can drive meters 10 to 13 feet of our EL wire OR 1 meter 3 feet of EL tape OR a 10cmx10cm piece of EL panel for about 7 hours.

There is a switch for selecting steady/blink/off modes. Comes with four 2.5mm pitch female JST connectors, standard for all the EL wire and tape we carry. The JST cables snap into the inverter, so if you don't need all 4 cables, you can use as few as you want. The inverter does not 'sequence' the 4 cables, so if you use 'blink mode' all the strands will blink at the same time. There is a 1.7mm DC jack on the side so you can put in to power this off of a different battery or power source, This cable has a matching DC plug on the end You can plug any of our EL wire/tape into this inverter directly. To connect a 'raw' piece EL wire to this, you'll want a male connector wire The EL inverter requires a 'load' to stabilize itself. Do not run the inverter without at least 2 ft of EL wire attached! Otherwise the inverter can spike and damage itself Like all inverters we've used, the 2000 Hz oscillation is slightly audible. To reduce the squeaking, we suggest opening up the case padding it with thick foam tape/weatherstripping. Squirting some hot glue around the capacitors may also help. We managed to get it silent this way. Check out our EL TRON bag tutorial for ideas! Soldering to raw EL wire is a little tricky but luckily we wrote a detailed tutorial! The tutorial also covers a lot of information about EL and how it works.

Technical Details

Dimensions o Inverter Size 85mm x 55mm x 22mm 3.4in x 2.2in x 0.85in o JST cable length approx. 20 cm o Weight without batteries 60g

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 564 Datasheet file may be downloaded here without warranties.

564

564 Datasheet

Datasheet ID: 564 514016