MP2-S150G-51M1-C-TR40B

MP2-S150G-51M1-C-TR40B Datasheet


MP2 Series

Part Datasheet
MP2-S150G-51M1-C-TR40B MP2-S150G-51M1-C-TR40B MP2-S150G-51M1-C-TR40B (pdf)
PDF Datasheet Preview
3M MetPak 2-FB Socket
2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers

MP2 Series
• End-to-end stackable
• Offset dual-beam contact minimizes insertion force
• Molded guide fingers provide integrated alignment
• Alignment wafer for true position
• Mates with MP2-P inverse headers and elevated inverse headers, MP2-PXXXE, for extended card applications
• Protective Push-Cap on Press-Fit Only
• Meets IEC 61076-4-104 global standard
• See Regulatory Information Appendix RIA for chemical compliance information

Date Modified April 6, 2007

Physical

Insulation Material High Temp LCP Flammability UL 94V-0
Color Beige Contact Material Copper Alloy Plating Underplating 50 um Nickel Wiping Area See Ordering Information Solder Tails See Ordering Information

Electrical

Current Rating Signal A - All contacts simultaneously Insulation Resistance 103 MΩ Withstanding Voltage 1000 VAC

Environmental

Temperature Rating -55°C to +125°C Process Temperature Rating 260°C Profile per J-STD-020C

Moisture Sensitivity Level 1 per J-STD-020C

TS-1117-06 Sheet 1 of 4

UL File No E68080
3M Interconnect Solutions

MetPak is a trademark of 3M Company. * Futurebus+ is a registered trademark of the Institute of Electrical and Electronic Engineers, Inc. IEEE .
3M is a trademark of 3M Company. For technical, sales or ordering information call
800-225-5373
3M MetPak 2-FB Socket
2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers

MP2 Series

ROW E D C B A

POSITION 1 2

TYP.

POSITION X
"C" TAIL LENGTH

PRESS-FIT AND SOLDER TAIL PRODUCT CAPPED

TYP. "B"

MATED WITH MP2-PXXXE-5XXX-XXXX

CENTER LINE OF ROW A

ASSEMBLED TO PCB AND MATED WITH MP2-PXXX-5XXX-XXXX

Note Refer to IEC 61076-4-104 global standard. "Press Fit" describes a contact tail having a compliant section designed to make a reliable electrical connection
with a plated through-hole PTH in a printed circuit board, typically a "back plane.”
[inch]

Tolerance Unless Noted
mm ±3
[ ] Dimensions for Reference Only
Ordering Information

MP2 - SXXXG - 5XXX-C -

S = Socket

Contact Count See Table

Guide Finger

Contact Arrangement

Rows
1 = All positions filled*
5 = 5 Rows

C = Capped Solder Tail Blank = Press-Fit

Tail Length See Table 2

Termination Style M = Solder Tail Press Peg P = Press-Fit w/Tail Cover
*Contact 3M Sales Representative for information on special fill patterns and mono blocked pairs.

Plating Options See Table 3

TS-1117-06 Sheet 2 of 4
3M Interconnect Solutions
3M is a trademark of 3M Company. For technical, sales or ordering information call
800-225-5373
3M MetPak 2-FB Socket
2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers

MP2 Series

Table 1 - Connector & Row Lengths

Pin Count
030 060 090 120 150 180 210 240

Dim. "A" mm [inch]

Dim "B" mm [inch]

Block Rows Count

Table 2 - Tail Length

Contact-to-PC Board Tail Termination Option No.

Dim. "C"

Solder

Press-Fit*
*Compliant-Pin Tail

Plating Suffix

Press-Fit Tails*

RIA E2 & C2 apply

TG30

RIA E2 & C2 apply

TR30

RIA E2 & C2 apply

TR40B

RIA E2 & C2 apply

RIA E1 & C1
apply

RIA E1 & C1 apply

RIA E1 & C1 apply

RIA E1 & C1 apply

RIA E1 & C1 apply
*Compliant-Pin Tail

Table 3 - Plating & Regulatory

Solder Tails

Plating Composition

RIA E3 & C2 apply
µm [10 µ"] Min. Au Contact Area µm [100 µ"] Min. SnPb Tail Area µm [50 µ"] Min. Ni all over

RIA E3 & C2 apply
µm [30 µ"] Min. Au Contact Area µm [100 µ"] Min. SnPb Tail Area µm [50 µ"] Min. Ni all over
µm [3 µ"] Min. Au Contact Area
3M is a trademark of 3M Company. For technical, sales or ordering information call
800-225-5373
3M MetPak 2-FB Socket
2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers

MP2 Series

TYP.

THESE HOLES CONSTITUTE MODULAR REPEATING PATTERN
“D” PLATED"D"THPLRAOTEUDGTHH-HRUOHLEOLE

UUNNPPLLAATETDEDTHTRHURHOOULEGH-HOLE

UUNNPPLALTAETDETDHTRHURHOOLUEGH-HOLE

RECOMMENDED PCB HOLE MOUNTING PATTERN

Table 4 -- HOLE PLATING For TG, TG30, TR30, TR40B FINISHES ONLY

HOLE

Finished Dia. mm [in]

Cu Thickness mm SnPb Thickness
[in]
microns [µ"]

Drilled Hole Dia. mm [in]
"D" min
15 [600] max

Table 5 -- HOLE PLATING For FJ, KR, RF, LR, and PD FINISHES ONLY

Hole

Finished Dia. mm [in]

Cu Thickness mm [in]

Immersion Matte Sn Thickness

Electrolitic Au Thickness
microns [µ"]
microns [µ"]

OSP ENTEK Thickness microns [µ"]

Drilled Hole Dia. mm [in]
- [20 - 100]
- [4 - 20]
- [8 - 20]
or 0.85mm [ #66] TWIST DRILL
3M Interconnect Solutions

TS-1117-06 Sheet 4 of 4
3M is a trademark of 3M Company. For technical, sales or ordering information call
800-225-5373

Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect

EUROPE

Appendix E1 European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part “Product” does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E2 European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part “Product” does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E3 European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E4 European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/17/EC. “RoHS Compliant 2005/95/EC” means that the product or part “Product” does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

RIA-2217-A

CHINA

Appendix C1 China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material a by weight for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers or b by weight for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix C2 China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material a by weight for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers or b by weight for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below.

Name and Content of Hazardous Substances or Elements

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty Limited Remedy Limited Liability. This product will be free from defects in material and manufacture for a period of ninety 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

Electronic Solutions Division
6801 River Place Blvd. Austin, TX 78726-9000 800/225-5373

RIA-2217-A 3M 2007
More datasheets: 32-6518-10 | 14-3518-10 | 28-6518-10 | 24-6518-10 | 24-3518-10 | 24-4518-10 | 22-4518-10 | 18-3518-10 | 64-9518-10 | U86-D1427-10121


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MP2-S150G-51M1-C-TR40B Datasheet file may be downloaded here without warranties.

Datasheet ID: MP2-S150G-51M1-C-TR40B 520741