MNHU10-250DFIK

MNHU10-250DFIK Datasheet

MNHU18-250DFI, MNHU14-250DFI, MNHU10-250DFI

Part	Datasheet
MNHU10-250DFIK	MNHU10-250DFIK (pdf)

PDF Datasheet Preview
Scotchlok Terminals MNHU18-250DFI, MNHU14-250DFI, MNHU10-250DFI Female Disconnect, Nylon/Heat Shrink Fully Insulated, Butted Seam Data Sheet Product Number Wire Range AWG MNHU18-250DFI 22-18 MNHU14-250DFI 16-14 MNHU10-250DFI 12-10 Male Tab Width x Thickness Barrel Length Barrel I.D. Specifications Wire Size Barrel Seam Maximum Voltage Rating: Maximum Temperature Rating Maximum Current Insulator Material: Terminal Material Plating: See Table Above Butted 600 V Building Wire 1000 V Signs or Fixtures Luminaires Same as Wire Nylon/Adhesive Lined Polyolefin Brass Tin Installation Information WARNING Turn power off before installing or removing terminal. All electrical work should be done according to appropriate electrical codes. For use on stranded copper wire only. Strip away the end 3/8 inch of wire insulation. Make the crimp in the proper station of a recommended 3M crimp tool TH-440, TH-450 scissor style hand tools. Barrel Crimp Electrical Shrink tubing using a heat gun. Heat until tubing is completely shrunk and adhesive protrudes slightly from the tubing. Engineering Specification Crimp-Type Female Disconnects shall, electrically and mechanically connect permanently to a prestripped end of a stranded copper wire and have a tongue portion with fingers which grip a male quick disconnect in a separable, reusable manner, forming a Quick Connect Wiring Connection. The connector line shall offer a tongue variations sized to grip Male Tabs x per ANSI/NEMA CD-2 and barrel variations in wire AWG size 22-18, 16-14, 12-10 and construction nylon fully insulated and polyolefin heatshrink material . The tongue shall be marked with the wire range and the manufacturer’s symbol The Nylon Fully Insulated Female Disconnect shall be tin plated thick brass, with a tongue for gripping a x male tab per ANSI/NEMA CD-2 and a barrel covered by a molded nylon funnel entry sleeve, which extends to cover the tongue, color coded, and sized for a specified AWG wire range 22-18, 16-14, Color coded adhesive lined heat shrink tubing extends from the crimp area beyond the terminal. The heat activated tubing conforms to the terminal and the adhesive bonds to the conductor. 3M and Scotchlok are trademarks of 3M IMPORTANT NOTICE Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Warranty Limited Remedy Limited Liability. This product will be free from defects in material and manufacture as of the date of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted. Electrical Products Division 6801 River Place Blvd. Austin, TX 78726-9000 Litho in USA. 3M 2002 78-8125-9932-8-B

PDF Datasheet Preview

Scotchlok Terminals

MNHU18-250DFI, MNHU14-250DFI, MNHU10-250DFI

Female Disconnect, Nylon/Heat Shrink Fully Insulated, Butted Seam

Data Sheet

Product Number

Wire Range AWG

MNHU18-250DFI 22-18

MNHU14-250DFI 16-14

MNHU10-250DFI 12-10

Male Tab Width x Thickness

Barrel Length

Barrel I.D.

Specifications

Wire Size Barrel Seam Maximum Voltage Rating:

Maximum Temperature Rating Maximum Current Insulator Material:

Terminal Material Plating:

See Table Above Butted 600 V Building Wire 1000 V Signs or Fixtures Luminaires Same as Wire Nylon/Adhesive Lined Polyolefin Brass Tin

Installation Information

WARNING

Turn power off before installing or removing terminal. All electrical work should be done according to appropriate electrical codes.

For use on stranded copper wire only. Strip away the end 3/8 inch of wire insulation. Make the crimp in the proper station of a recommended 3M crimp tool TH-440, TH-450 scissor style hand tools.

Barrel Crimp Electrical

Shrink tubing using a heat gun. Heat until tubing is completely shrunk and adhesive protrudes slightly from the tubing.

Engineering Specification

Crimp-Type Female Disconnects shall, electrically and mechanically connect permanently to a prestripped end of a stranded copper wire and have a tongue portion with fingers which grip a male quick disconnect in a separable, reusable manner, forming a Quick Connect Wiring Connection.

The connector line shall offer a tongue variations sized to grip Male Tabs x per ANSI/NEMA CD-2 and barrel variations in wire AWG size 22-18, 16-14, 12-10 and construction nylon fully insulated and polyolefin heatshrink material . The tongue shall be marked with the wire range and the manufacturer’s symbol

The Nylon Fully Insulated Female Disconnect shall be tin plated thick brass, with a tongue for gripping a x male tab per ANSI/NEMA CD-2 and a barrel covered by a molded nylon funnel entry sleeve, which extends to cover the tongue, color coded, and sized for a specified AWG wire range 22-18, 16-14, Color coded adhesive lined heat shrink tubing extends from the crimp area beyond the terminal. The heat activated tubing conforms to the terminal and the adhesive bonds to the conductor.
3M and Scotchlok are trademarks of 3M

IMPORTANT NOTICE Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use.

Warranty Limited Remedy Limited Liability. This product will be free from defects in material and manufacture as of the date of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted.

Electrical Products Division
6801 River Place Blvd. Austin, TX 78726-9000

Litho in USA. 3M 2002 78-8125-9932-8-B

More datasheets: AT27LV512A-90JC | AT27LV512A-70JC | AT27LV512A-70RC | AT27LV512A-90RC | MAN6980 | MAN6940_LHI | MAN6960 | MAN6940 | MAN6910 | 3624

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MNHU10-250DFIK Datasheet file may be downloaded here without warranties.

Datasheet ID: MNHU10-250DFIK 520686